鈑金加工在噴漆技術中的應用顧名思義,就是面漆最后一道工序,待漆面干固后處理其上面的瑕疵,盡了**的努力都會流下一部分不十分完美的地方,那就只有后期補救了,其實噴涂得再滿意的漆面都不是十分完美的,比如〈奔馳〉〈寶馬〉的裝車油漆都會有輕微的細魚鱗狀現象,我們通稱桔皮現象,這是漆膜在流平過程中的干燥時差所產生的自然現象,當然一般人是難以察覺的,要用專家級的欣賞水平才能發覺,所以要騙過專家的眼睛,就只有進行漆面處理了,我們稱為“鏡面處理”。先用1500-2000目的美容砂紙進行整平研磨〈有必要時可用2500目的〉,然后用浮巖或陶土成分組成的粗蠟進行磨切,處理掉砂紙痕跡,下一步用細切蠟進行研磨〈不含硅〉,處理掉粗蠟痕跡,然后用還原劑處理以達到完美光澤,再用鏡面處理劑徹底清除光環及抹痕,這時油漆以達到最深層光澤了,最后一道工序就是封釉,這樣就可以達到專家級的完美漆面效果了。 |